The
ultimate in varnish performance, combining excellent chemical and
abrasion resistance with superb gloss. The improved formulation of
Perfection Plus contains UV filters to give it the longest possible
life.
* Fully compatible with oily woods like teak and iroko after adequate degreasing and substrate preparation
* Chemical cure gives resistance to fuels, oil and mild acids and alkalis
* Up to four times longer service life than ordinary varnishes |
|
| Colour |
YVA950-Clear |
| Finish |
High Gloss |
| Specific Gravity |
1.065 |
| Volume Solids |
45.3% |
| Mix Ratio |
2:1 by volume (as supplied) , Converter/Curing Agent - YVA951 |
| Typical Shelf Life |
2 yrs |
| VOC (As Supplied) |
520 g/lt |
| VOC (EU Solvent) |
488 g/kg EU Solvent Emissions Directive (Council Directive 1999/13/EC) |
| Unit Size |
750 ml |
|
|
|
Drying |
|
10°C |
15°C |
23°C |
35°C |
|
|
| Touch Dry [ISO] |
10hrs |
7hrs |
4hrs |
3hrs |
| Pot Life |
4hrs |
3hrs |
2hrs |
1hrs |
|
|
Overcoating |
|
Substrate Temperature |
| |
10°C |
15°C |
23°C |
35°C |
| Overcoated By |
Min |
Max |
Min |
Max |
Min |
Max |
Min |
Max |
|
|
| Perfection Plus |
24hrs |
4days |
14hrs |
3days |
6hrs |
2days |
4hrs |
1days |
|
| Preparation |
PREVIOUSLY PAINTED SURFACES:
In Good Condition: Wash down with Super Cleaner, rinse with fresh water and allow to dry. Abrade with 320-400 grade (grit) paper.
In Poor Condition: Remove all previous coatings and prime the substrate.
BARE WOOD:
Sand smooth with 120 grade paper, followed by 240 and finally 320 grade
paper. Remove sanding dust by brushing, dusting and wiping. If wiping
with solvent then allow to dry completely before applying the first
coat. Prime, if required, with International's Clear Wood Sealer
Standard (Polygrond) and Clear Wood Sealer Fast Dry.
If Clear Wood Sealer has been omitted thin the first coat by 20-25% with Thinner No.9.
OILY WOODS e.g. Teak:
Must be adequately degreased (Thinners No.9 is recommended) and
prepared prior to application of Perfection Plus. Please ensure the
surface is completely dry before applying the first coat. |
|
|
| Hints |
Mixing Stir
individual products prior to mixing. Mix the base and curing agents of
Perfection Plus together at the specified mix ratio. Add curing agent
to the base, stir and leave for 10 minutes to allow bubbles to
disperse. Avoid using direct from the can. Mix the amount you expect to
use in a separate container.
Note: Any initial cloudiness will disappear upon thorough mixing.
Thinner YTA006 Thinners No.9
Thinning Thin first coat 20-25% when applied direct to bare wood. Thin other coats as required.
Cleaner YTA006 Thinners No.9
Conventional Spray Do not spray.
Roller Use foam rollers. For best results when applying by roller, smooth off with a pad or brush. |
|
|
| Some Important Points |
Apply
in dry, well ventilated conditions. Best applied at ambient
temperatures of between 15°C and 20°C. Sensitive to moisture during
application. Avoid relative humidity levels above 80%. Avoid applying
late in the evening as condensation can cause a loss of gloss during
overnight cure. Do not apply in direct sunlight. Use above the
waterline only. |
|
|
| Compatibility/Substrates |
Apply
over bare wood, International's Clear Wood Sealer Standard (Polygrond)
or Clear Wood Sealer Fast Dry. Ensure all sanding residues are removed
before application of the Perfection Plus.
Will crack on carvel
and clinker/lapstrake hulls. Do not use Perfection Plus on flexible
constructions. Do not apply over any conventional, one pack products. |
|
|
| Number of Coats |
2
- 5 (First coat thinned). Over bare wood apply 1 thinned coat (25%) +
minimum 4 full coats, apply 2 full coats over Clear Wood Sealer
Standard and Fast Dry. Apply 1 full coat if used as a Clear Coat.
The number of coats should be increased if applied by roller. |
|
|
| Coverage |
(Theoretical) - 13.30 (m²/lt) |
|
|
| Recommended DFT |
37 microns dry by brush/roller
|
| Recommended WFT |
75 microns wet by brush/roller |
|
|
| Application Methods |
Brush, Roller |
|
| Storage |
GENERAL INFORMATION:
Exposure
to air and extremes of temperature should be avoided. For the full
shelf life of this product to be realised ensure that between use the
container is firmly closed and the temperature is between 5°C/40°F and
35°C/95°F. Keep out of direct sunlight.
TRANSPORTATION:
Perfection Plus should be kept in securely closed containers during transport and storage.
|
|
|
| Safety |
GENERAL:
Always use gloves and goggles and keep skin protected with overalls.
Users should ensure they have a copy of the Material Safety Datasheet
for this product and that they are familiar with all the safety
directions before use. Read the label safety section for Health and
Safety Information, also available from our Technical Help Line.
DISPOSAL:
Do not discard tins or pour paint into water couses, use the facilities
provided. It it best to allow paints to harden before disposal. |
|
| IMPORTANT NOTES |
The
information given in this sheet is not intended to be exhaustive. Any
person using the product without first making further written enquiries
as to the suitability of the product for the intended purpose does so
at their own risk and we can accept no responsibility for the
performance of the product or for any loss or damage (other than death
or personal or injury resulting from negligence) arising out of such
use. The information contained in this sheet is liable to modification
from time to time in the light of experience and our policy of
continuous product development. |
|
  , International,
the AkzoNobel logo and other products mentioned in this publication are
trademarks of, or licensed to Akzo Nobel. ©Akzo Nobel 2009. |
|
Head Office
International Paint Ltd
26th Floor, Portland House
Bressenden Place
London SW1E 5BG
United Kingdom
tel: +44 (0) 20 7932 9900
fax: +44 (0) 20 7932 9932 |
European Region
International Paint Ltd
1 Wellington Park
Hedge End, Southampton
Hampshire SO30 2QU
United Kingdom
tel: +44 (0) 1489 775050
fax: +44 (0) 1489 785867 |
Asia Region
International Paint Singapore (Pte) Ltd
449 Tagore Industrial Avenue
01-03 Greatland Industrial Building
Singapore 787820
tel: +65 6453 1981
fax: +65 6453 1778 |
Australasia Region
International Paint
Unit E54, 76 Waterway Drive
Coomera Qld 4209
Australia
tel: +61 (0) 7 5573 9600
fax: +61 (0) 7 5573 9677 |
North America Region
International Paint LLC
2270 Morris Avenue
Union
New Jersey 07083
USA
tel: +1 (0) 908 686 1300
fax: +1 (0) 908 686 8545 |
South America Region
International Paint
Rod Rap tavares, KM 18.5
Predio Administrativo 11
Butanta CEP 05577-300
Sao Paulo, Brazil
tel: +55 (0) 11 3789 2000
fax: +55 (0) 11 3789 2200 |
|
